Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Microstructure and some properties of powder-pack borided Ti–5Mo–5V–8Cr–3Al alloy with special attention to the microstructure at the interface TiB/substrate

The borided layer was prepared on the surface of the Ti–5Mo–5V–8Cr–3Al alloy by powder-pack boriding at 1000°C-10h. SEM, EPMA and TEM were used to investigate the effects of alloying elements (Al, V, Mo and Cr) on the growth of TiB whiskers in the borided Ti–5Mo–5V–8Cr–3Al alloy. Wear properties of borided Ti–5Mo–5V–8Cr–3Al alloy were investigated using dry reciprocating friction tests. SEM results show that the thickness of boride layer in Ti–5Mo–5V–8Cr–3Al alloy is thinner than that in the Cp-Ti. This is attributed to the enrichment of alloying elements especially V in TiB/substrate by TEM, which hinders the diffusion of B atoms, thus resulting in the short and thick TiB whiskers in Ti–5Mo–5V–8Cr–3Al alloy. Borided Ti–5Mo–5V–8Cr–3Al alloy has the better wear resistance than as-received alloy.     

渗流作用下新型装配重力式挡土墙有限元分析

为研究渗流作用下新型装配重力式挡土墙应力变化及墙体排水通道对墙后土体固结的影响,采用ABAQUS进行有限元分析,有限元分析结果与模型试验结果相吻合,证明该模型的合理性。在此基础上研究渗流作用下墙体应力变化趋势及墙体排水通道对墙后土体固结效果的影响。研究结果表明:横向排水通道对墙后土体固结效果的影响优于纵向排水通道对土体固结效果的影响,墙体底部横向排水通道的影响作用最显著;渗流作用下墙体应力由上往下呈先增大后减小的趋势,墙体下部所受最大水平剪应力最大。     

Effects of TGO growth on the stress distribution and evolution of three-dimensional cylindrical thermal barrier coatings based on finite element simulations

Based on the ultrasonic C-scan results of 8YSZ coatings after thermal cycles, three-dimensional cylindrical numerical simulations of the physical geometry model of the thermal barrier coating (TBC) sinusoidal surfaces were conducted with finite elements to estimate the stress distribution and evolution law of the top coat (TC)/bond coat (BC) interface, including the centre and edge of the specimen affected by the dynamic growth of the thermally grown oxide (TGO). The results show that when a layer of TGO is grown on the TC/BC interface, compressive stress is uniformly distributed on the TGO interface, and the stress value decreases as a function of the TGO layer thickness. When the thickness of the TGO exceeds a certain value, the compressive stress of all parts of the interface gradually changes to tensile stress; meanwhile, the edges of the model affected by the crest and trough effects of the wave are reflected in the radial and circumferential directions, especially along the axial direction, with alternating concentrated tensile and compressive stresses. TGO growth imposes a minor influence on the magnitude and distributions of the radial and circumferential stresses at the BC interface. The linear elasticity, creep, fatigue, and stress accumulation effects of each layer of TBCs in each thermal cycle were fully considered in this model. The model not only interprets the crest and trough effects of the TC/BC surface interface during the growth of TGO, but also interprets the effects of the core and edge of the cylindrical model, further revealing the reason for which the core and edge of the TBC will most likely form cracks.     

Design,synthesis, structure,and stability of novel multi-principal element (Ti,Zr,Hf,W)C ceramic with a miscibility gap

Here we design a novel multi-principal element carbide system (Ti,Zr,Hf,W)C with a miscibility gap using computational tools and report on the formation of a single-phase (Ti,Zr,Hf,W)C after spark plasma sintering. The (Ti,Zr,Hf,W)C shows high nanohardness (32.7 GPa) and fracture toughness (5 MPa·m^1/2). Aging studies at 1350 °C for 100 h show that the single-phase carbide solid solution is quite stable even though this temperature is within the predicted miscibility gap of the system. Detailed electron microscopy characterization shows that phase separation has initiated with minor decomposition after aging by forming rock-salt (Ti,W)C- and (Zr,Hf)C-rich phases as well as hexagonal WC precipitates. We show that the (Ti,W)C- and (Zr,Hf)C-rich phases form a lamellar structure upon aging and the interlamellar spacing is considerably coarser than what has been previously found for the binary (Ti,Zr)C system. The decomposition kinetics, on the other hand, is sluggish due to the reduced driving force for phase decomposition.     

Numerical modeling of wave propagation in anisotropic viscoelastic laminated materials in transient regime: Application to modeling ultrasonic testing of composite structures

Composite laminate structures remain an important family of materials used in cutting-edge industrial areas. Building efficient numerical modeling tools for high-frequency wave propagation in order to represent ultrasonic testing experiments of these materials remains a major challenge. In particular, incorporating attenuation phenomena within anisotropic plies, and thin intermediate isotropic layers between the plies often represent significant obstacles for standard numerical approaches. In our work, we address both issues by proposing a systematic study of the fully discrete propagators associated to the Kelvin-Voigt, Maxwell, and Zener models, and by incorporating effective transmission conditions between plies using the mortar element method. We illustrate the soundness of our approach by proposing intermediate one-dimensional and two-dimensional numerical evidence, and we apply it to a more realistic configuration of a curved laminate composite structure in a three-dimensional setting.     

Kevlar织物软壁包容环抗冲击数值仿真分析研究

针对机匣包容性问题,提出Kevlar平纹织物本构模型的拟合方法,分别采用单层壳、多层壳、层合壳三种有限元建模方式对Kevlar织物软壁包容环弹道冲击过程进行模拟,发展了机匣包容性仿真分析模型。结果表明,多层壳模型和层合壳模型的计算结果更准确,并且可以通过调节摩擦因子使仿真结果与试验结果更接近。在此基础上研究了撞击点位置和弹体入射姿态对弹体剩余速度的影响。结果表明:在较小偏移距离内,撞击点的位置对剩余速度的影响可以忽略不计;滚转角和俯仰角对剩余速度影响较小,而对于偏航角,当角度大于30°时,剩余速度会随着角度的增大明显呈下降趋势,且弹体出射姿态也会发生明显变化。     

H∞ control for uncertain one‐sided Lipschitz nonlinear systems in finite frequency domain

The current article discusses the H_∞ disturbance attenuation control design problem for one‐sided Lipschitz systems in finite frequency domain. Models containing norm‐bounded parameter uncertainties, disturbances, and input nonlinearities are considered. By contrast to existing full frequency methods, the H_∞ controller is computed depending on the frequency ranges of disturbances. The finite frequency disturbance attenuation index is initially defined. Thanks to Finsler's lemma, sufficient and less conservative analysis conditions are also derived for the closed‐loop system. Then, synthesis conditions in the low, middle, and high frequency ranges as well as the whole frequency range, are formulated in terms of linear matrix inequalities. At last, to prove the effectiveness and the superiority of the proposed approach, a physical example is used and a comparative study is done.     

Passive target detection and tracking from electromagnetic field measurements

This paper presents a novel approach to the localization of moving targets in a complex environment based on the measurement of the perturbations induced by the target presence on an independently‐generated time‐varying electromagnetic field. Field perturbations are measured via a set of sensors deployed over the domain of interest and used to detect and track a possible target by resorting to a particle Bernoulli filter (PBF). To comply with real‐time operation, the PBF works along with an artificial neural network (ANN) model of the environment trained offline via finite elements (FEs). The performance of the proposed algorithm is assessed via simulation experiments.     

矿用直线振动筛结构故障分析

针对煤矿选煤厂直线振动筛工作过程中出现的结构故障问题,采用有限元仿真与现场测试结合的方法对振动筛出现故障的原因进行了分析研究。介绍了振动筛的主要结构及常见故障,并以某矿选煤厂发生大梁断裂的振动筛为例,对该振动筛进行三维建模和有限元模态分析,分析结果表明:随着模态阶次的增加,振型的变化逐渐由移动转为结构本身的扭曲变形。在该振动筛空载工作状态下,选用本质安全型便携式测振记录仪进行振动测试并处理测试信号,得到该振动筛的工作频率。结合模态分析结果和实际测试结果,判断出空载时频繁运行振动筛是造成其大梁断裂的主要原因。根据故障原因给出维护建议:应当尽量避免振动筛在空载或物料较少的状态下长时间运行;在振动筛投入使用前,应预先了解振动筛的工作状态及可能存在的薄弱环节,尽可能避免结构故障,保证振动筛可靠运行。